Delta-electronics Power Output Module DVPPS02 User Manual download pdf

Warning

 This instruction will be helpful in the installation, electronic specification, function specification and

troubleshooting of the DVPPS01 and DVPPS02.

 This is an OPEN TYPE DVPPS series. The DVPPS series should be kept in an enclosure away from airborne dust,

high humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as some special

tools or keys to open the enclosure, so as to avoid the hazard to users and the damage to the DVPPS series.

 Never connect the AC main circuit power supply to any of the output terminals, as it will damage the DVPPS series.

Check all the wiring prior to power up. To avoid any electromagnetic noise, make sure the DVPPS series is properly

grounded .



Introduction

Thank you for choosing DELTA DVP series. DVPPS series is a power module with 2 types that sorted by output

circuit. 1. DVPPS01 provides 24V DC and 1A current for output power. 2. DVPPS02 provides 24V DC and 2A

current for output power. DVPPS series is only used for Delta DVP series. DVPPS series is separated from the

PLC MPU for better space utilization and easier installation.

 Product Profile & Outline

DVPPS01

13. 3

36. 5

DV PPS 01

Unit: mm

DVPPS02

13.3 60

100

32.5

DVP PS02

Unit: mm

Power LED

I/O terminal label

Output/input terminal (fixed terminal)

Nameplate

DIN rail clip

Mounting holes

DIN rail track (35mm)

 Electrical Specifications

Model

Item

DVPPS01 DVPPS02

Power input 100 ~ 240VAC (-15% ~ +10%), 50/60Hz 100 ~ 240VAC (-15% ~ +10%), 50/60Hz

Output power 24VDC (±3%), output current: 1A max. 24VDC (±3%), output current: 2A max.

Ripple & noise Under 100mV

p-p

Typical at full load Under 240mV

p-p

Typical at full load

Efficiency 78% ~ 87% Typical at full load

Over load/short circuit

protection

Auto Recovery

Grounding

The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and

N (All PLC units should be grounded directly to the ground pole).

Operation/storage

environment

Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), Pollution degree 2;

Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)

Agency approvals

Underwriters Laboratories, Inc.: UL508 Listed (Industrial Control Equipment)

European Community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC

Weight (g) 158 250

ENGLISH

 Installation and Wiring

 Mounting Arrangements and Wiring

DIN Rail Installation:

The DVPPS can be sec

ured to a cabinet by using the DIN rail that

is 35mm high with a depth of 7.5mm. When mounting the DVPPS

on the DIN rail, be sure to use the end bracket to stop any

side-to-side motion of the DVPPS, thus to reduce the chance of

the wires being pulled loose. On the bottom of the DVPPS is a

small retaining clip. To secure the DVPPS to the DIN rail, place it

onto the rail and gently push up on the clip. To remove it, pull

down on the retaining clip and gently pull the DVPPS away from

the DIN rail. Please see the figure on the right:

For heat dissipation. Make

sure to provide a minimum

clearance of 50mm

between the unit and all

sides of the cabinet. (as

shown below)

DVP MPU

> 50mm> 50mm

> 50mm

Direct mounting: Tighten M4 screws into direct mount hole.

Wiring:

To suit M3.5 screw terminals

Below 6.2

1. Please use O-type or Y-type terminals for I/O wiring terminals. The specification

for the terminals is as shown on the left. Tighten PLC terminal screws to a torque

of 5 ~ 8kg-cm (4.3 ~ 6.9 in-lbs).

2. Please avoid tiny metal material enter DVPPS01/DVPPS02 when screwing and

wiring. After finishing wire, remove the affix that pasted on the heat sink for heat

dissipation.

3. Use Copper Conductors Only, 60°C.

 Wiring Notes

 Environment

1. DO NOT store the DVPPS01/DVPPS02 in a dusty, smoky, or corrosive atmosphere.

2. DO NOT store the DVPPS01/DVPPS02 in an environment with high temperature or high humidity.

3. DO NOT install PLC on a shelf or on an unstable surface.

 Power Input Wiring

Power input of DVPPS01/DVPPS02 is AC input; following items should be noticed:

1. Connect the AC input (100VAC ~ 240VAC) to terminals L and N. Any 110VAC or 220VAC connected to the

+24V terminal will permanently damage the DVPPS01/DVPPS02.

2. Please use wires of 1.6mm and above for the grounding.

3. If the power-cut time is less than 10ms, the DVPPS01/DVPPS02 still operates unaffectedly. If the

power-cut time is too long, the DVPPS01/DVPPS02 will stop operating and all the outputs will be Off.

 Trial Run

 Power indicator, Running and Test

The “POWER” LED at the front of DVPPS01/DVPPS02 will be lit (in green) if the power is on. If the indicator

is not ON, it indicates that the power supply is not enough or short circuit. Please check your power wiring.

 Troubleshooting

Judge the errors by the indicators on the front panel. When errors occurred on DVPPS01/DVPPS02, please

check:

 “POWER” LED

The “POWER” LED at the front of the MPU will be lit (in green) if the power is on. If the indicator is not on

when the MPU is powered up, please check if power supply is normal. If the indicator is not on when the MPU

is powered up and with the input power being normal, it is an indication that the PLC is malfunction. Please

have this machine replaced or have it repaired at a dealer near you.



 (OPEN TYPE) /

( : )

 /



DVP DVPPS 2 1. DVPPS01

24V DC 1A 2. DVPPS02 24V DC 2A DVPPS DVP



DVPPS01

13.3

36.5

DVPP S0 1

DVPPS02

13.3 60

100

32.5

3 3

DV PPS 02

/ ( )

DIN

DIN (35mm)



DVPPS01 DVPPS02

100 ~ 240VAC (-15% ~ +10%), 50/60Hz 100 ~ 240VAC (-15% ~ +10%), 50/60Hz

24VDC (±3%), : 1A 24VDC (±3%), : 2A

& 100mV

p-p

240mV

p-p

78% ~ 87%

L, N PLC

0°C ~ 55°C 50 ~ 95% 2

-25°C ~ 70°C 5 ~ 95%

: UL508 Listed (Industrial Control Equipment)

89/336/EEC 73/23/EEC

( , g) 158 250

1 2

Summary of Contents

Page 1 - DVPP S0 1

Warning  This instruction will be helpful in the installation, electronic specification, function specification and troubleshooting of the DVPPS0

Page 2 - DV PPS01

 DIN 35mm DIN DVPPSDVPPSDVPPSDVPPSPLC M4 PLCPLC DVP MPU50mm50mm50mm50mm 6.2M3.56.2 1. / O Y PLC 5 ~ 8kg-cm (4.3 ~ 6.9 in-lbs) 2. PLC PLC 3.

Comments to this Manuals

No comments

Delta-electronics Power Output Module DVPPS02 User Manual

Browse online or download User Manual for Tools Delta-electronics Power Output Module DVPPS02. Delta Electronics Power Output Module DVPPS02 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Delta-electronics Power Output Module DVPPS02